BS EN ISO 19069-1:2015 BSl Standards Publication Plastics Polypropylene (PP) moulding and extrusion materials Part 1: Designation system and basis for specifications bsi. ..making excellence a habit: BS ENISO19069-1:2015 BRITISH STANDARD National foreword This British Standard is the UK implementation of EN ISO 19069-1:2015. It supersedes BS EN ISO 1873-1:1995 which is withdrawn. The UK participation in its preparation was entrusted to Technical Committee PRI/82,Thermoplastic materials. A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. @The British Standards Institution 2015 Published by BSI Standards Limited 2015 ISBN9780580831591 ICS83.080.20 Compliance with a British Standard cannot confer immunity from legal obligations. This British Standard was published under the authority of the Standards Policy and Strategy Committee on31March2015. Amendments/corrigenda issued sincepublication Date Text affected EN ISO 19069-1 EUROPEANSTANDARD NORME EUROPEENNE EUROPAISCHENORM March 2015 ICS 83.080.20 Supersedes EN ISO1873-1:1995 English Version Plastics - Polypropylene (PP) moulding and extrusion materials Part 1:Designation system and basis for specifications (isO 19069-1:2015) Plastiques - Materiaux polypropylene (PP) pour moulage et Kunststoffe - Polypropylen (PP)-Formmassen - Teil 1: extrusion - Partie 1: Systeme de designation et base de Bezeichnungssystem und Basis fur Spezifikationen (ISO specification (ISO 19069-1:2015) 19069-1:2015) This European Standard was approved by CEN on 10 January 2015. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Siovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. rer EUROPEAN COMMITTEE FOR STANDARDIZATION COMITE EUROPEEN DE NORMALISATION EUROPAISCHES KOMITEE FUR NORMUNG CEN-CENELEC Management Centre:Avenue Marnix 17, B-100o Brussels @2015CEN All rights of exploitation in any form and by any means reserved Ref.No.ENISO19069-1:2015E worldwide for CEN national Members BS EN ISO 19069-1:2015 EN ISO 19069-1:2015 (E) Foreword This document (EN ISO 19069-1:2015) has been prepared by Technical Committee ISO/TC 61 "Plastics" in text or by endorsement, at the latest by September 2015, and conflicting national standards shall be withdrawn at the latest by September 2015. rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. This document supersedes EN ISO 1873-1:1995. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Endorsementnotice BSENISO19069-1:2015 IS0 19069-1:2015(E) Contents Page Foreword iv 1 Scope 1 2 Normativereferences 1 3 Designation and specification system 2 3.1 22 General 3.2 Data block 1 3.3 Datablock2 3 3.4 Datablock3 4 3.5 Datablock4 4 3.5.1 General. 4 3.5.2 Tensi